Then, press the power button for around 30 seconds and you should hear a fan spinning and hard drive clicking. If you can’t boot the computer, unplug the battery or unplug the power cord. If you’ve tried all the basic steps but still cannot turn on your HP laptop, you probably have a faulty CPU. If you find a faulty chip in the laptop, you should contact Hp Laptop Service Center in Greater Kailash to find out what to do. If the blinking continues, the CPU is probably the problem. If you notice a white light or caps lock blinking, the battery is likely dead. To diagnose the faulty CPU, first open the battery compartment. When you are facing the problem of an HP laptop not turning on, it may be due to the faulty CPU. Then, wait a few minutes and press the Power button again. If your HP laptop still has the power issue, you must reboot it manually by holding down the Power button for 15 seconds. Then, close all programs and devices and remove any USB-connected devices. To perform the reset process, turn off the HP laptop and make sure there are no external devices plugged into the machine. The procedure involves downloading and installing the latest BIOS file from HP’s website. Depending on the model of your HP laptop, this process may take a few hours. To fix this issue, you should attempt to restore the BIOS to its default settings. If you are experiencing problems with your HP laptop, it is possible that it is suffering from a faulty BIOS. To remove it, you need to press and hold the power button for about 30 seconds. Usually, this is located near the motherboard. If you want to fix the HP laptop not turning on power light blinking issue, you must first check the BIOS battery. In case the battery is damaged, it may not be easy to replace it. To avoid this problem, follow these tips to repair the battery in your HP laptop. However, you should never let the battery completely drain, as this can damage the laptop. In most cases, the battery is under warranty, so you can purchase a new one without affecting the laptop’s warranty. If you’re experiencing HP laptop not turning on issues, one of the most common solutions is to replace the faulty battery. Here are some solutions that may work for your HP laptop. However, if the problem persists, you may need to replace the entire computer. If all of these options fail to work, try replacing the battery. The battery, the BIOS, or the CPU may be faulty. Logicaldrive 3 (465.7 GB, 0): Transforming, 0.If the power light of your HP laptop is blinking and not turning on, there are several possible causes of this problem. ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 modify rebuildpriority=high On the server I am looking at, I do not see that option under System in the Tasks tab. Physicaldrive 2I:1:6 (port 2I:box 1:bay 6, 500 GB): OK ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld all show status

~ Migrate RAID0 to RAID1 online with hpacucli ~ # /opt/hp/hpssacli/bin/hpssacli rescan ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 create type=ld drives=2I:1:5 raid=0Ĭonfirm new disk creation by checking status of all Logical Disks ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld all show status Notice new HDD 2I:1:5 Create new Raid 0 Logical Disk using HDD 2I:1:5 ~ # Physicaldrive 2I:1:5 (port 2I:box 1:bay 5, 500 GB): OK Physicaldrive 1I:1:4 (port 1I:box 1:bay 4, 146 GB): OK The Server originally came installed with two 146GB SAS 10k single port hard drives. Physicaldrive 1I:1:3 (port 1I:box 1:bay 3, 146 GB): OK Storage & Backup Data Storage HP DL 380 G5 Hard Drives Flashing Orange Posted by alee786 on Feb 22nd, 2014 at 10:48 PM Solved Data Storage Hello, I recently upgraded our HP DL 380 G5 Server with 6 additional drives.

Physicaldrive 1I:1:2 (port 1I:box 1:bay 2, 72 GB): OK Physicaldrive 1I:1:1 (port 1I:box 1:bay 1, 72 GB): OK ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 pd all show status Use the 'show' command for more information. ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld 3 modify raid=1Įrror: The logical drive is in a state which prevents this operation fromĬompleting. ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld 3 add drives=allunassigned ~ # Scan for new HardDisk ~ # /opt/hp/hpssacli/bin/hpssacli rescan Check status for all Logical Disks ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 ld all show statusĬheck Status of all Physical Disks ~ # /opt/hp/hpssacli/bin/hpssacli ctrl slot=0 modify rebuildpriority=high Enjoy Check ESXi Version ~ # esxcli -version As usual, since it took me to search around Google, I simply decided to document it for future references, after all it’s just easier to read your own instructions than someone elses. It was picking it up via vCenter and I found that because I am using HP server hpssacli command was the only (best way?) way to add this new disk as RAID 0 (I had just 1 disk as my other one failed). I ran into some snag when I tried to add a new HDD to my ESXi server.

Turn on disk led hp